Heli-max HMXE07 Manuel d'utilisateur

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.C

10Moving the cyclic stick forward (away from you) will cause the helicopter to tilt forward and start moving that direction.Moving the collective stic

11TRACKING THE MAIN BLADESAt zero pitch, bring the main rotor up to speed and observe whether the rotational planes of the blades are the same. If the

12transitions. This will allow you to practice nose-in and still give you a chance to get out of trouble. As you improve you’ll remain nose-in for lon

13SERVO SETUPNote: The AXE CP V3 RTF is factory set-up and test fl own so there is no need to make these adjustments unless you have damaged or changed

by pulling outward. Remove the dampening spacer. Pull on the other blade grip and remove the spindle and blade grip. If the O-rings come loose, simply

15MAIN SHAFT INSTALLATIONUsing the 1.5mm hex wrench and pliers to hold the nut, re-install the lower main shaft bolt.Insert a 1.5mm hex wrench into th

16Solder a Micro Deans plug onto the motor wires of the C-12 ESC as shown. The negative (–) motor lead (blue wire) connects to the male pin on the con

17Since the E-Board provides power to the receiver and servos, the BEC in the C-12 ESC must be disabled. Carefully lift up the plastic tab on the C-12

18ORDERING PARTSReplacement parts for the Heli-Max AXE CP V3 RTF are available using the order numbers in the Parts List on page 18. The fastest, most

19596060EXPLODED VIEWDETAILED VIEW OF ROTOR HEAD

2TABLE OF CONTENTSINTRODUCTION ... 2AMA ...

20LiPo Battery 1 PC950 mAh 11.1VPart # GPMP0401EVPL # 4Antenna Tube 1 PCPart # HMXE4703EVPL # 5Can

21Screw Set 40 PCSPart # HMXE7342EVPL # 8Silicon Secture T

22OPTIONAL PARTSCF 3D Vertical Fin w/Hardware (1 Set)Part # HMXE7450CF 3D Horiz Fin w/Hardware (1 Set)Part # HMXE7451CF 3D Flybar Paddles (2 Pcs)Part

23Great Planes 11.1V, 950 mAh Axe CP V3 LiPo BatteryPart # GPMP0401ElectriFly PolyCharge™ LiPo ChargerPart # GPMM3010ElectriFly Triton2™ ChargerPart #

Entire Contents © Copyright 2008HMXE07xxMNL01

2. You must assemble the model according to the instructions. Do not alter or modify the model, as doing so may result in an unsafe or unfl yable model

HMXP1004 3S LiPo CHARGER SPECIFICATIONS Input voltage: 12V DC Battery types, # cells: 3 lithium-polymer cells connected in Series (11.1V LiPo)Char

5ASSEMBLY INSTRUCTIONSINSTALL BATTERIES IN THE TRANSMITTER❏ 1. Remove the battery cover from the back of the transmitter. Remove the battery box and i

666that the battery is being charged. If the charger indicator light turns to green immediately, then the battery is already fully charged.❏ 4. When t

7ASSEMBLE TRAINING GEAR❏ 1. Snap the four plastic fi ttings onto the landing gear as shown. Slide the carbon rods through the underside of the fi ttings

8transmitter on, you should be able to walk at least 50 feet away from the model and still have control. Have an assistant stand by your model and whi

9CONTROLSAlways turn the transmitter on fi rst and verify the idle up switch is set to normal. With the AXE CP V3 sitting still, plug the battery into