Heli-max HMXM1015 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Heli-max HMXM1015. Heli-Max HMXM1015 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 15
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
All pictures, descriptions, and
specications found in this
instruction manual are subject to
change without notice. Heli-Max®
maintains no responsibility for
inadvertent errors in this manual.
HMXM1015 MNL
HM4050 AVCS
HEADING LOCK GYRO
Thank you for purchasing the Heli-Max
HM4050 Heading Lock Gyro.
Please take the time to read this
manual fully before installing your gyro.
MANUAL SPECIFICATION
& DESCRIPTION CHANGES
HM4050 gyro with connectors
Foam adhesive tape
Manual
INCLUDES
AVCS
(Angular Vector Control System)
Small size
Lightweight
Able to operate in Heading Hold
as well as Normal ight mode
Remote or local selectable
Digital or analog servo capable
LED power indicator
Perfect for small,
lightweight helicopters
FEATURES
3.6 to 5.5V
Operating
Voltage:
3.6 to 5.5V
Operating
Voltage:
< 1%Precision: < 1%Precision:
< 2ms (Digital Servo)Response: < 2ms (Digital Servo)Response:
< 10ma
Operation
Current:
< 10ma
Operation
Current:
800 deg per sec MAXRotation: 800 deg per sec MAXRotation:
.35oz (9.9g)Weight: .35oz (9.9g)Weight:
.437” (12mm)Height: .437” (12mm)Height:
.800” (20.3mm)Width: .800” (20.3mm)Width:
.800” (20.3mm)Length: .800” (20.3mm)Length:
SPECS
®
Vue de la page 0
1 2 3 4 5 6 ... 14 15

Résumé du contenu

Page 1 - HEADING LOCK GYRO

All pictures, descriptions, and specications found in this instruction manual are subject to change without notice. Heli-Max® maintains no responsibi

Page 2

10Adjust the SENS (gain) dial to a higher percentage for more gain or lower for less.NOTE: Dialing back the SENS (gain) dial too far will limit the tr

Page 3 - Rudder Servo Preparation

11If you set both values to a positive percentage, switch up and switch down, you can obtain two heading hold gain values in the same  ight program;

Page 4

12Other AdjustmentsDual RateThis is used to add or subtract how far the tail blades de ect. Using dual rates one can have two (or more depending on t

Page 5

13The helicopter rotates faster in one direction than the other.Check the installation of the servo to make sure it’s properly installed as well as do

Page 6 - Gyro Installation

14Warranty ServiceHeli-Max® will warrant your Gyro for 90 days after the purchase from defects in materials or workmanship of original manufacture. He

Page 8 - Gyro Setup

2HM4050 Switch and Dial Explanation1 Light Emitting Diode (LED): The LED will glow green anytime the gyro is powered and operating. (NOTE: If the lig

Page 9 - Gyro Use

3Installing the HM4050 in Your HelicopterRudder Servo PreparationWARNING: In this step it is best to unplug the motor or move the motor pinion gear a

Page 10

44 Install the servo arm such that the arm is 90 degrees to the tail boom. If you cannot obtain 90 degrees, try a few di erent servo arms or wheels u

Page 11

56 Next, pivot the tail blades so both blades are pointing up. Adjust the length of the rudder pushrod so the distance between the blade tips is 18 t

Page 12 - Trouble Shooting Guide

67 Check the mechanical limits by moving the rudder stick all the way to the right and then all the way to the left. Adjust end points (left and righ

Page 13

72 The orientation of the gyro’s sensor is such that the label of the gyro faces up. Clean the area with an alcohol pad and attach the gyro using the

Page 14 - Warranty Service

84 Attach the 3 wire male connector (rudder) from the gyro to channel 4 of your receiver (Futaba®). Also, plug the one wire plug from the gyro (gain)

Page 15

96 Adjust the DIR switch so the gyro provides the proper compensation. To check this, grasp the helicopter holding the tail away from you. Swing or r

Commentaires sur ces manuels

Pas de commentaire